[nanopi neo2] [boot image vmdb2-wrapper]

Discussions sur les cartes Nanopi R1, Neo, K1, etc.)
https://www.friendlyarm.com/
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

[nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,

Vous trouverez ci-joint le boot de la nanopi neo2 réalisé à partir du projet de Jérôme : vmdb2-wrapper.
La spécification de la carte est ici http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO2

Pour rappel, la production logicielle (décrite dans le fichier yaml relatif à la board) se résume ainsi ...

Code: Select all

 sudo vmdb2 nanopi-neo2_buster_arm64_vmdb2-0.14.1.yaml --output nanopi-neo2_buster_arm64.img --rootfs-tarball buster_arm64_rootfs.tgz --log=stderr
Après flashage sur une SD classe 10, et installation du tty de debug, le résultat est le suivant :

Code: Select all


U-Boot SPL 2020.04-armbian (Sep 02 2020 - 09:22:27 +0200)
DRAM: 512 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.3(debug):d35403f-dirty
NOTICE:  BL31: Built : 09:22:24, Sep  2 2020
NOTICE:  BL31: Detected Allwinner H5 SoC (1718)
NOTICE:  BL31: Found U-Boot DTB at 0x4090ab0, model: FriendlyARM NanoPi NEO 2
INFO:    ARM GICv2 driver initialized
INFO:    Configuring SPC Controller
NOTICE:  PMIC: Assuming H5 reference regulator design
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!
NOTICE:  PSCI: System suspend is unavailable
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9


U-Boot 2020.04-armbian (Sep 02 2020 - 09:22:27 +0200) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: FriendlyARM NanoPi NEO 2
DRAM:  512 MiB
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... In:    serial
Out:   serial
Err:   serial
NanoPi NEO2 v1.0 detected
Net:   phy interface7
eth0: ethernet@1c30000
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1d000: USB EHCI 1.00
Bus usb@1c1d400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1d000 for devices... 1 USB Device(s) found
scanning bus usb@1c1d400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
2330 bytes read in 3 ms (757.8 KiB/s)
## Executing script at 4fc00000
26922880 bytes read in 1285 ms (20 MiB/s)
20662 bytes read in 6 ms (3.3 MiB/s)
26669480 bytes read in 1273 ms (20 MiB/s)
Booting Debian 5.10.0-0.bpo.4-arm64 from mmc 0:1...
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
EHCI failed to shut down host controller.
   Loading Ramdisk to 48690000, end 49fff1a8 ... OK
   Loading Device Tree to 0000000048687000, end 000000004868f0b5 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.10.0-0.bpo.4-arm64 (debian-kernel@lists.debian.org) (gcc-8 (Debian 8.3.0-6) 8.3.0, GNU ld (GNU Binutils for Debian) 2.31.1) #1 SMP Debian 5.10.19-1~bpo10+1 (2021-03-13)
[    0.000000] Machine model: FriendlyARM NanoPi NEO 2
[    0.000000] efi: UEFI not found.
[    0.000000] cma: Reserved 64 MiB at 0x000000005c000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x5bee5b00-0x5bee7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 33 pages/cpu s95192 r8192 d31784 u135168
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200 root=UUID=6831b3cb-ec52-462b-9249-eee246678f51 net.ifnames=0 apparmor=0 cgroup_enable=memory loglevel=7
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] Memory: 386908K/524288K available (11392K kernel code, 2418K rwdata, 6932K rodata, 5440K init, 586K bss, 71844K reserved, 65536K cma-reserved)
[    0.000000] random: get_random_u64 called from __kmem_cache_create+0x34/0x4f0 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 39180 entries in 154 pages
[    0.000000] ftrace: allocated 154 pages with 4 groups
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4.
[    0.000000] 	Rude variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000274] Console: colour dummy device 80x25
[    0.000425] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000445] pid_max: default: 32768 minimum: 301
[    0.000633] LSM: Security Framework initializing
[    0.000712] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.000758] SELinux:  Initializing.
[    0.000871] TOMOYO Linux initialized
[    0.000972] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.000988] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.003839] rcu: Hierarchical SRCU implementation.
[    0.006211] EFI services will not be available.
[    0.006802] smp: Bringing up secondary CPUs ...
[    0.008173] Detected VIPT I-cache on CPU1
[    0.008266] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.009333] Detected VIPT I-cache on CPU2
[    0.009383] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.010383] Detected VIPT I-cache on CPU3
[    0.010426] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.010533] smp: Brought up 1 node, 4 CPUs
[    0.010563] SMP: Total of 4 processors activated.
[    0.010573] CPU features: detected: 32-bit EL0 Support
[    0.010583] CPU features: detected: CRC32 instructions
[    0.010592] CPU features: detected: 32-bit EL1 Support
[    0.024087] CPU: All CPU(s) started at EL2
[    0.024162] alternatives: patching kernel code
[    0.026321] devtmpfs: initialized
[    0.033340] Registered cp15_barrier emulation handler
[    0.033372] Registered setend emulation handler
[    0.033388] KASLR disabled due to lack of seed
[    0.033854] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.033915] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.037027] pinctrl core: initialized pinctrl subsystem
[    0.038011] DMI not present or invalid.
[    0.038870] NET: Registered protocol family 16
[    0.041404] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.041539] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.041673] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.041766] audit: initializing netlink subsys (disabled)
[    0.041988] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1
[    0.043505] thermal_sys: Registered thermal governor 'fair_share'
[    0.043511] thermal_sys: Registered thermal governor 'bang_bang'
[    0.043520] thermal_sys: Registered thermal governor 'step_wise'
[    0.043528] thermal_sys: Registered thermal governor 'user_space'
[    0.043535] thermal_sys: Registered thermal governor 'power_allocator'
[    0.043989] cpuidle: using governor ladder
[    0.044023] cpuidle: using governor menu
[    0.044265] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.044415] ASID allocator initialised with 65536 entries
[    0.044901] Serial: AMBA PL011 UART driver
[    0.069071] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.069098] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.069107] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.069116] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.922056] ACPI: Interpreter disabled.
[    0.922346] iommu: Default domain type: Translated 
[    0.922683] vgaarb: loaded
[    0.923153] EDAC MC: Ver: 3.0.0
[    0.925000] NetLabel: Initializing
[    0.925013] NetLabel:  domain hash size = 128
[    0.925019] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.925141] NetLabel:  unlabeled traffic allowed by default
[    0.925748] clocksource: Switched to clocksource arch_sys_counter
[    1.028953] VFS: Disk quotas dquot_6.6.0
[    1.029066] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.029916] pnp: PnP ACPI: disabled
[    1.040656] NET: Registered protocol family 2
[    1.041658] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.041707] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    1.041837] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    1.041938] TCP: Hash tables configured (established 4096 bind 4096)
[    1.042185] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.042219] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.042468] NET: Registered protocol family 1
[    1.042504] NET: Registered protocol family 44
[    1.042524] PCI: CLS 0 bytes, default 64
[    1.042870] Trying to unpack rootfs image as initramfs...
[    2.806325] Freeing initrd memory: 26044K
[    2.807870] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    2.808082] kvm [1]: IPA Size Limit: 40 bits
[    2.809945] kvm [1]: vgic interrupt IRQ9
[    2.810150] kvm [1]: Hyp mode initialized successfully
[    2.812414] Initialise system trusted keyrings
[    2.812481] Key type blacklist registered
[    2.812784] workingset: timestamp_bits=42 max_order=17 bucket_order=0
[    2.821615] zbud: loaded
[    2.823203] integrity: Platform Keyring initialized
[    2.823227] Key type asymmetric registered
[    2.823237] Asymmetric key parser 'x509' registered
[    2.823296] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    2.823651] io scheduler mq-deadline registered
[    2.829839] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[    2.835024] sun50i-h5-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    2.836277] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    2.845107] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    2.847503] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator
[    2.848228] printk: console [ttyS0] disabled
[    2.868440] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 30, base_baud = 1500000) is a U6_16550A
[    3.684430] printk: console [ttyS0] enabled
[    3.689902] Serial: AMBA driver
[    3.693383] msm_serial: driver initialized
[    3.698733] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    3.705874] mousedev: PS/2 mouse device common for all mice
[    3.712877] sun6i-rtc 1f00000.rtc: registered as rtc0
[    3.717958] sun6i-rtc 1f00000.rtc: hctosys: unable to read the hardware clock
[    3.725104] sun6i-rtc 1f00000.rtc: RTC enabled
[    3.731095] ledtrig-cpu: registered to indicate activity on CPUs
[    3.737378] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    3.745960] NET: Registered protocol family 10
[    3.800607] Segment Routing with IPv6
[    3.804409] mip6: Mobile IPv6
[    3.807441] NET: Registered protocol family 17
[    3.812089] mpls_gso: MPLS GSO support
[    3.816495] registered taskstats version 1
[    3.820615] Loading compiled-in X.509 certificates
[    4.019398] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[    4.028228] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5abca669825178e052c84667ccbc0531f8c'
[    4.038615] zswap: loaded using pool lzo/zbud
[    4.043610] Key type ._fscrypt registered
[    4.047639] Key type .fscrypt registered
[    4.051568] Key type fscrypt-provisioning registered
[    4.085629] Freeing unused kernel memory: 5440K
[    4.117358] Checked W+X mappings: passed, no W+X pages found
[    4.123087] Run /init as init process
Loading, please wait...
Starting version 241
[    4.547490] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pd not found, using dummy regulator
[    4.561666] sun8i-h3-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator
[    4.578536] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator
[    4.607124] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pg not found, using dummy regulator
[    4.616444] sun4i-usb-phy 1c19400.phy: Couldn't get regulator usb0_vbus... Deferring probe
[    4.632299] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pg not found, using dummy regulator
[    4.649936] pps_core: LinuxPPS API ver. 1 registered
[    4.654997] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    4.658468] usbcore: registered new interface driver usbfs
[    4.663616] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    4.674431] usbcore: registered new interface driver hub
[    4.678591] PTP clock support registered
[    4.680008] usbcore: registered new device driver usb
[    4.703247] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.704058] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    4.719277] ehci-platform: EHCI generic platform driver
[    4.725278] ehci-platform 1c1a000.usb: EHCI Host Controller
[    4.731021] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    4.739657] ehci-platform 1c1a000.usb: irq 19, io mem 0x01c1a000
[    4.740302] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.756297] libphy: Fixed MDIO Bus: probed
[    4.757837] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    4.769462] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    4.769969] ohci-platform: OHCI generic platform driver
[    4.777833] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.783560] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    4.787536] mmc0: host does not support reading read-only switch, assuming write-enable
[    4.790283] usb usb1: Product: EHCI Host Controller
[    4.790290] usb usb1: Manufacturer: Linux 5.10.0-0.bpo.4-arm64 ehci_hcd
[    4.790295] usb usb1: SerialNumber: 1c1a000.usb
[    4.792250] mmc0: new high speed SDHC card at address e624
[    4.798935] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator
[    4.799254] hub 1-0:1.0: USB hub found
[    4.799313] hub 1-0:1.0: 1 port detected
[    4.799902] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    4.800127] ohci-platform 1c1a400.usb: irq 20, io mem 0x01c1a400
[    4.800632] ehci-platform 1c1d000.usb: EHCI Host Controller
[    4.800654] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 3
[    4.800786] ehci-platform 1c1d000.usb: irq 21, io mem 0x01c1d000
[    4.807640] mmcblk0: mmc0:e624 SC16G 14.8 GiB 
[    4.812424] musb-hdrc musb-hdrc.2.auto: MUSB HDRC host driver
[    4.813842] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00
[    4.814267] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    4.814274] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.814280] usb usb3: Product: EHCI Host Controller
[    4.814286] usb usb3: Manufacturer: Linux 5.10.0-0.bpo.4-arm64 ehci_hcd
[    4.814291] usb usb3: SerialNumber: 1c1d000.usb
[    4.822507] hub 3-0:1.0: USB hub found
[    4.834694]  mmcblk0: p1
[    4.835876] hub 3-0:1.0: 1 port detected
[    4.852283] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found
[    4.859720] musb-hdrc musb-hdrc.2.auto: new USB bus registered, assigned bus number 4
[    4.862176] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    4.862186] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.862192] usb usb2: Product: Generic Platform OHCI controller
[    4.862197] usb usb2: Manufacturer: Linux 5.10.0-0.bpo.4-arm64 ohci_hcd
[    4.862203] usb usb2: SerialNumber: 1c1a400.usb
[    4.862813] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found
[    4.863109] hub 2-0:1.0: USB hub found
[    4.863156] hub 2-0:1.0: 1 port detected
[    4.864256] ohci-platform 1c1d400.usb: Generic Platform OHCI controller
[    4.864288] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 5
[    4.864478] ohci-platform 1c1d400.usb: irq 22, io mem 0x01c1d400
[    4.871271] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    4.877202] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    4.881111] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.886912] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 50006 (expect 58000)
[    4.892996] usb usb4: Product: MUSB HDRC host driver
[    5.010208] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[    5.015766] usb usb4: Manufacturer: Linux 5.10.0-0.bpo.4-arm64 musb-hcd
[    5.015772] usb usb4: SerialNumber: musb-hdrc.2.auto
[    5.016937] hub 4-0:1.0: USB hub found
[    5.024126] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[    5.029923] hub 4-0:1.0: 1 port detected
[    5.037114] dwmac-sun8i 1c30000.ethernet: COE Type 2
[    5.047320] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    5.051358] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[    5.051365] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[    5.051376] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[    5.058597] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.066271] libphy: stmmac: probed
[    5.070236] usb usb5: Product: Generic Platform OHCI controller
[    5.070253] usb usb5: Manufacturer: Linux 5.10.0-0.bpo.4-arm64 ohci_hcd
[    5.076917] dwmac-sun8i 1c30000.ethernet: Found internal PHY node
[    5.081293] usb usb5: SerialNumber: 1c1d400.usb
[    5.082757] hub 5-0:1.0: USB hub found
[    5.086875] libphy: mdio_mux: probed
[    5.090505] hub 5-0:1.0: 1 port detected
[    5.098748] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY
[    5.168195] dwmac-sun8i 1c30000.ethernet: Powering internal PHY
[    5.186822] libphy: mdio_mux: probed
[    5.190482] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 
/dev/mmcblk0p1: recovering journal
[    5.495265] random: fast init done
/dev/mmcblk0p1: clean, 21985/196608 files, 225067/786176 blocks
done.
[    5.997409] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.284522] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
SELinux:  Could not open policy file <= /etc/selinux/targeted/policy/policy.33:  No such file or directory
[    6.901797] systemd[1]: System time before build time, advancing clock.
[    6.989241] systemd[1]: Inserted module 'autofs4'
[    7.095416] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    7.117531] systemd[1]: Detected architecture arm64.

Welcome to Debian GNU/Linux 10 (buster)!

[    7.183966] systemd[1]: Set hostname to <NanoPiNEO2>.
[    7.802875] random: systemd: uninitialized urandom read (16 bytes read)
[    7.814921] random: systemd: uninitialized urandom read (16 bytes read)
[    7.821650] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    7.842012] random: systemd: uninitialized urandom read (16 bytes read)
[    7.849068] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[    7.873942] systemd[1]: Reached target Remote File Systems.
[  OK  ] Reached target Remote File Systems.
[    7.894797] systemd[1]: Listening on Journal Socket (/dev/log).
[  OK  ] Listening on Journal Socket (/dev/log).
[    7.918760] systemd[1]: Listening on udev Control Socket.
[  OK  ] Listening on udev Control Socket.
[    7.942856] systemd[1]: Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Audit Socket.
[    7.971054] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on fsck to fsckd communication Socket.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Listening on Journal Socket.
         Starting udev Coldplug all Devices...
         Mounting Kernel Debug File System...
         Mounting Huge Pages File System...
         Starting Load Kernel Modules...
         Starting Remount Root and Kernel File Systems...
[  OK  ] Started Dispatch Password …ts to Console Directory Watch.
[  OK  ] Reached target Local Encrypted Volumes.
[  OK  ] Reached target Paths.
[    8.266801] EXT4-fs (mmcblk0p1): re-mounted. Opts: errors=remount-ro
         Mounting POSIX Message Queue File System...
[  OK  ] Listening on Syslog Socket.
         Starting Journal Service...
         Starting Create list of re…odes for the current kernel...
[  OK  ] Reached target Slices.
[  OK  ] Set up automount Arbitrary…s File System Automount Point.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Started Create list of req… nodes for the current kernel.
[  OK  ] Started Journal Service.
         Starting Load/Save Random Seed...
         Starting Flush Journal to Persistent Storage...
         Starting Create System Users...
         Starting Apply Kernel Variables...
[  OK  ] Started udev Coldplug all Devices.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Create System Users.
[  OK  ] Started Apply Kernel Variables.
         Starting Create Static Device Nodes in /dev...
         Starting Helper to synchronize boot up for ifupdown...
[    8.784147] systemd-journald[187]: Received request to flush runtime journal from PID 1
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting Create Volatile Files and Directories...
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Update UTMP about System Boot/Shutdown...
         Starting Network Time Synchronization...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[    9.506071] mc: Linux media interface: v0.10
[    9.511567] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz)
[    9.534472] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    9.554716] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    9.562810] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    9.573544] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    9.582306] sun8i-ce 1c15000.crypto: Register cbc(aes)
[  OK  ] Started Network Time Synchronization.
[  OK  ] Reached target System Time Synchron[    9.611252] cryptd: max_cpu_qlen set to 1000
ized.
[    9.616131] videodev: Linux video capture interface: v2.00
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Started Daily rotation of log files.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[    9.725143] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[  OK  ] Reached target Basic System.
[    9.752066] sunxi_cedrus: module is from the staging directory, the quality is unknown, you have been warned.
         Starting System Logging Service...
[    9.783421] cedrus 1c0e000.video-codec: Device registered as /dev/video0
[  OK  ] Started Regular background program processing daemon.
         Starting Login Service...
[  OK  ] Started D-Bus System Message Bus.
[    9.898082] lima 1e80000.gpu: gp - mali450 version major 0 minor 0
[  OK  ] Started Daily Cleanup of Temporary [    9.905357] lima 1e80000.gpu: pp0 - mali450 version major 0 minor 0
Directories.
[    9.917323] lima 1e80000.gpu: pp1 - mali450 version major 0 minor 0
[    9.925233] lima 1e80000.gpu: pp2 - mali450 version major 0 minor 0
[  OK  ] Reached target Timers.[    9.933212] lima 1e80000.gpu: pp3 - mali450 version major 0 minor 0

[    9.944073] lima 1e80000.gpu: l2 cache 8K, 4-way, 64byte cache line, 128bit external bus
[    9.952347] lima 1e80000.gpu: l2 cache 128K, 4-way, 64byte cache line, 128bit external bus
[    9.973424] lima 1e80000.gpu: bus rate = 200000000
[    9.978401] lima 1e80000.gpu: mod rate = 384000000
[    9.987005] [drm] Initialized lima 1.1.0 20191231 for 1e80000.gpu on minor 0
[  OK  ] Started System Logging Service.
[  OK  ] Found device /dev/ttyS0.
[  OK  ] Started Login Service.
[   10.444485] sun8i-ce 1c15000.crypto: Fallback for cbc-aes-sun8i-ce is cbc-aes-ce
[   10.455612] sun8i-ce 1c15000.crypto: Register ecb(aes)
[   10.461138] sun8i-ce 1c15000.crypto: Fallback for ecb-aes-sun8i-ce is ecb-aes-ce
[   10.471020] sun8i-ce 1c15000.crypto: Register cbc(des3_ede)
[   10.532686] sun8i-ce 1c15000.crypto: Fallback for cbc-des3-sun8i-ce is cbc(des3_ede-generic)
[   10.543407] sun8i-ce 1c15000.crypto: Register ecb(des3_ede)
[   10.580112] sun8i-ce 1c15000.crypto: Fallback for ecb-des3-sun8i-ce is ecb(des3_ede-generic)
[   10.590629] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0
[  OK  ] Started Helper to synchronize boot up for ifupdown.
         Starting Raise network interfaces...
[   10.945073] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:07] driver [RTL8211E Gigabit Ethernet] (irq=POLL)
[   10.957362] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found
[   10.964776] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available
[   10.972501] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW
[   10.979944] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii link mode
[*     ] A start job is running for Raise network interfaces (8s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (8s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (9s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (9s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (10s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (11s / 5min 2s)
[    **] A start job is running for Raise network interfaces (11s / 5min 2s)
[     *] A start job is running for Raise network interfaces (12s / 5min 2s)
[    **] A start job is running for Raise network interfaces (12s / 5min 2s)
[   20.710165] random: crng init done
[   20.713722] random: 7 urandom warning(s) missed due to ratelimiting
[   ***] A start job is running for Raise network interfaces (13s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (14s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (14s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (15s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (15s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (16s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (17s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (17s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (18s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (18s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (19s / 5min 2s)
[    **] A start job is running for Raise network interfaces (20s / 5min 2s)
[     *] A start job is running for Raise network interfaces (20s / 5min 2s)
[    **] A start job is running for Raise network interfaces (21s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (21s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (22s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (23s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (23s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (24s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (24s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (25s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (26s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (26s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (27s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (27s / 5min 2s)
[   35.805784] usb0-vbus: disabling
[    **] A start job is running for Raise network interfaces (28s / 5min 2s)
[     *] A start job is running for Raise network interfaces (29s / 5min 2s)
[    **] A start job is running for Raise network interfaces (29s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (30s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (30s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (31s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (32s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (32s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (33s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (33s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (34s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (35s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (35s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (36s / 5min 2s)
[    **] A start job is running for Raise network interfaces (36s / 5min 2s)
[     *] A start job is running for Raise network interfaces (37s / 5min 2s)
[    **] A start job is running for Raise network interfaces (38s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (38s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (39s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (39s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (40s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (41s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (41s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (41s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (42s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (42s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (43s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (43s / 5min 2s)
[    **] A start job is running for Raise network interfaces (44s / 5min 2s)
[     *] A start job is running for Raise network interfaces (44s / 5min 2s)
[    **] A start job is running for Raise network interfaces (45s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (45s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (46s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (46s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (47s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (47s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (48s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (48s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (49s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (49s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (50s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (50s / 5min 2s)
[    **] A start job is running for Raise network interfaces (51s / 5min 2s)
[     *] A start job is running for Raise network interfaces (51s / 5min 2s)
[    **] A start job is running for Raise network interfaces (52s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (52s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (53s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (53s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (54s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (54s / 5min 2s)
[*     ] A start job is running for Raise network interfaces (55s / 5min 2s)
[**    ] A start job is running for Raise network interfaces (55s / 5min 2s)
[***   ] A start job is running for Raise network interfaces (56s / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (56s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (57s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (57s / 5min 2s)
[    **] A start job is running for Raise network interfaces (58s / 5min 2s)
[     *] A start job is running for Raise network interfaces (58s / 5min 2s)
[    **] A start job is running for Raise network interfaces (59s / 5min 2s)
[   ***] A start job is running for Raise network interfaces (59s / 5min 2s)
[  *** ] A start job is running for Raise network interfaces (1min / 5min 2s)
[ ***  ] A start job is running for Raise network interfaces (1min / 5min 2s)
[***   ] A start job is running for Raise ne…ork interfaces (1min 1s / 5min 2s)
[**    ] A start job is running for Raise ne…ork interfaces (1min 1s / 5min 2s)
[*     ] A start job is running for Raise ne…ork interfaces (1min 2s / 5min 2s)
[**    ] A start job is running for Raise ne…ork interfaces (1min 2s / 5min 2s)
[***   ] A start job is running for Raise ne…ork interfaces (1min 3s / 5min 2s)
[ ***  ] A start job is running for Raise ne…ork interfaces (1min 3s / 5min 2s)
[  OK  ] Started Raise network interfaces.
[  OK  ] Reached target Network.
         Starting OpenBSD Secure Shell server...
         Starting Permit User Sessions...
[  OK  ] Started Permit User Sessions.
[  OK  ] Started Getty on tty1.
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Debian GNU/Linux 10 NanoPiNEO2 ttyS0

NanoPiNEO2 login: root
Last login: Thu Feb 14 10:15:34 UTC 2019 on ttyS0
Linux NanoPiNEO2 5.10.0-0.bpo.4-arm64 #1 SMP Debian 5.10.19-1~bpo10+1 (2021-03-13) aarch64

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
root@NanoPiNEO2:~# 
On est un peu surpris du choix de l'industriel sur l'adresse MAC, puisque le préfix est conforme IANA du plan d'adressage local, donc attention si présence de cet équipement sur une réseau public (!), pour un futur IOT, c'est surprenant (!)

Code: Select all

root@NanoPiNEO2:~# ip link ls 
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
    link/ether 02:01:eb:1f:a3:30 brd ff:ff:ff:ff:ff:ff
root@NanoPiNEO2:~# 
Un problème constaté (une fois de plus !) sur ces boards est lié au fait qu'en déconnectantt l'alimentation USB et en la rebranchant, la carte ne redémarre pas car probablement une sombre histoire d'alimentation par le canal de communication du câble série. :evil: .
De fait, dans ce cas là, il convient de débrancher également le port série de debug et l'alimentation et attendre 10 secondes avant de rebrancher le tout (!).
Inutile d'expliquer que dans ces conditions , la commande reboot ne risque pas de fonctionner (!)

..reste à vérifier que le port réseau est opérationnel ...

conclusions pour le moment
plutôt OK
:D
Cordialement
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,

Concernant les tests de l'interface réseau, avec l'installation décrite dans le post précédent, lors du branchement d'un câble Ethernet, j'ai ...

Code: Select all

[20165.729437] dwmac-sun8i 1c30000.ethernet eth0: Link is Down                                                                          
[20175.389504] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:07] driver [RTL8211E Gigabit Ethernet] (irq=POLL)                            
[20175.401937] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found                                                      
[20175.409408] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available                                                  
[20175.417108] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW                                                               
[20175.423695] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii link mode                                                   
[20179.518624] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx                                          
[20179.527050] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready                                                                  
Le problème est qu'après ajout d'une adresse IPV4, le test du ping ne fonctionne pas.
Une piste éventuelle serait liée au fait que le fimware de ce composant est donc basé sur un Realtek, et actuellement, l'image vmdb2 ne contient que ....

Code: Select all

[root@NanoPiNEO2:~# dpkg -l |grep firmware                                                                                               
ii  firmware-linux-free              3.4                          all          Binary firmware for various drivers in the Linux kernel  
root@NanoPiNEO2:~# 
Sur un autre équipement (pinebook), on peut constater que le paquet Debian firmware-realtek semble bien contenir ce firmware puisque ...

Code: Select all

ansible@pinebook-290:~$ uname -a
Linux pinebook-290 5.10.0-5-arm64 #1 SMP Debian 5.10.24-1 (2021-03-19) aarch64 GNU/Linux
ansible@pinebook-290:~$ cat /etc/debian_version 
10.9
ansible@pinebook-290:~$ dpkg -L  firmware-realtek |grep 821
/lib/firmware/rtl_bt/rtl8821a_fw.bin
/lib/firmware/rtl_bt/rtl8821c_config.bin
/lib/firmware/rtl_bt/rtl8821c_fw.bin
/lib/firmware/rtlwifi/rtl8821aefw.bin
/lib/firmware/rtlwifi/rtl8821aefw_29.bin
/lib/firmware/rtlwifi/rtl8821aefw_wowlan.bin
/lib/firmware/rtw88/rtw8821c_fw.bin
ansible@pinebook-290:~$ 
A suivre ....
:evil:
Cordialement
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,

Afin de tenter de trouver le problème du port Ethernet non opérationnel sur une Debian Buster fabriquée avec vmdb2-wrapper, j'ai reflashé une Armbian dans la version suivante :
Armbian_21.02.3_Nanopineo2_buster_current_5.10.21.img
La bonne nouvelle est que la version du driver du noyau semble identique a celle du noyau Debian, puisque un dchlient sur la nanopieo2 sur une infrastructure réseau acceptant cet équipement indique ....

Code: Select all

[  859.394073] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:07] driver [RTL8211E Gigabit Ethernet] (irq=POLL)                                                                                                               
[  859.396518] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found                                                                                                                                         
[  859.396541] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available                                                                                                                                     
[  859.396556] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW                                                                                                                                                  
[  859.396583] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii-id link mode                                                                                                                                   
[  878.430822] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:07] driver [RTL8211E Gigabit Ethernet] (irq=POLL)                                                                                                               
[  878.433823] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found                                                                                                                                         
[  878.433856] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available                                                                                                                                     
[  878.433871] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW                                                                                                                                                  
[  878.433898] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii-id link mode                                                                                                                                   
[  882.526889] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx                                                                                                                             
[  882.526967] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready                                      
Ce qui est déjà un bon début :D , mais à priori totalement identique au comportement décrit plus haut dans le post précédent avec le noyau de Debian
En revanche, la partie réseau est plus pertinente ici puisque ....

Code: Select all

root@nanopineo2: ~root@nanopineo2:~# dhclient -v eth0
Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/70:8b:cd:05:8f:4d
Sending on   LPF/eth0/70:8b:cd:05:8f:4d
Sending on   Socket/fallback
DHCPREQUEST for 192.168.95.32 on eth0 to 255.255.255.255 port 67
DHCPNAK from 192.168.31.17
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPOFFER of 192.168.95.32 from 192.168.95.17
DHCPREQUEST for 192.168.95.32 on eth0 to 255.255.255.255 port 67
DHCPNAK from 192.168.31.17
DHCPNAK from 192.168.79.17
DHCPACK of 192.168.95.32 from 192.168.95.17
/etc/resolvconf/update.d/libc: Warning: /etc/resolv.conf is not a symbolic link to /etc/resolvconf/run/resolv.conf
bound to 192.168.95.32 -- renewal in 241 seconds.
0;root@nanopineo2: ~root@nanopineo2:~# 
..et ..

Code: Select all

root@nanopineo2: ~root@nanopineo2:~# ping -c 2 google.fr
PING google.fr (216.58.211.195) 56(84) bytes of data.
64 bytes from mrs09s11-in-f3.1e100.net (216.58.211.195): icmp_seq=1 ttl=111 time=1639 ms
64 bytes from mrs09s11-in-f3.1e100.net (216.58.211.195): icmp_seq=2 ttl=111 time=663 ms

--- google.fr ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 9ms
rtt min/avg/max/mdev = 662.840/1151.030/1639.221/488.191 ms, pipe 2
root@nanopineo2: ~root@nanopineo2:~#
Tout est donc OK sur une image Armbian
Concernant le firmware, sur Armbian, on a :

Code: Select all

~root@nanopineo2:~# dpkg -l |grep firmware
ii  armbian-firmware                     21.02.3                             all          Linux firmware
0;root@nanopineo2:
Hélas, rien sur ce composant Ethernet, puisque ....

Code: Select all

0;root@nanopineo2: ~root@nanopineo2:~# dpkg -L armbian-firmware |grep -i rtl82
0;root@nanopineo2: ~root@nanopineo2:~#
La séquence de boot suivante permet peut re d'expliquer le pourquoi du comment ?

Code: Select all

U-Boot SPL 2020.10-armbian (Mar 08 2021 - 19:05:26 +0000)
DRAM: 512 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.4(debug):2c62b00-dirty
NOTICE:  BL31: Built : 19:05:15, Mar  8 2021
NOTICE:  BL31: Detected Allwinner H5 SoC (1718)
NOTICE:  BL31: Found U-Boot DTB at 0x40902c8, model: FriendlyARM NanoPi NEO 2
INFO:    ARM GICv2 driver initialized
INFO:    Configuring SPC Controller
NOTICE:  PMIC: Assuming H5 reference regulator design
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
INFO:    BL31: cortex_a53: CPU workaround for 1530924 was applied
INFO:    PSCI: Suspend is unavailable
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9


U-Boot 2020.10-armbian (Mar 08 2021 - 19:05:26 +0000) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: FriendlyARM NanoPi NEO 2
DRAM:  512 MiB
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... In:    serial
Out:   serial
Err:   serial
NanoPi NEO2 v1.0 detected
Net:   phy interface7
eth0: ethernet@1c30000
** Reading file would overwrite reserved memory **
Failed to load '/boot/boot.bmp'
There is no valid bmp file at the given address
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1d000: USB EHCI 1.00
Bus usb@1c1d400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1d000 for devices... 1 USB Device(s) found
scanning bus usb@1c1d400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Autoboot in 1 seconds, press <Space> to stop
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3202 bytes read in 3 ms (1 MiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
232 bytes read in 2 ms (113.3 KiB/s)
31031 bytes read in 6 ms (4.9 MiB/s)
504 bytes read in 5 ms (97.7 KiB/s)
Applying kernel provided DT overlay sun50i-h5-usbhost1.dtbo
504 bytes read in 5 ms (97.7 KiB/s)
Applying kernel provided DT overlay sun50i-h5-usbhost2.dtbo
4191 bytes read in 5 ms (818.4 KiB/s)
Applying kernel provided DT fixup script (sun50i-h5-fixup.scr)
## Executing script at 45000000
10049561 bytes read in 481 ms (19.9 MiB/s)
21792776 bytes read in 1040 ms (20 MiB/s)
Moving Image from 0x40080000 to 0x40200000, end=41730000
## Loading init Ramdisk from Legacy Image at 4fe00000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    10049497 Bytes = 9.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
EHCI failed to shut down host controller.
   Loading Ramdisk to 4966a000, end 49fff7d9 ... OK
   Loading Device Tree to 00000000495fa000, end 0000000049669fff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.10.21-sunxi64 (root@hirsute) (aarch64-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 2.32.0.20190321) #21.02.3 SMP Mon Mar 8 00:45:13 UTC 2021
[    0.000000] Machine model: FriendlyARM NanoPi NEO 2
[    0.000000] cma: Reserved 128 MiB at 0x0000000058000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x57eda100-0x57edbfff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 22 pages/cpu s50520 r8192 d31400 u90112
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: root=UUID=6e8b6a3b-ab26-496b-ae49-e5c30651ae15 rootwait rootfstype=ext4 console=ttyS0,115200 consoleblank=0 loglevel=7 ubootpart=d18206e9-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 14128(86%)
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 342832K/524288K available (13566K kernel code, 1058K rwdata, 4104K rodata, 2496K init, 352K bss, 50384K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x368/0x51c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000275] Console: colour dummy device 80x25
[    0.000380] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000398] pid_max: default: 32768 minimum: 301
[    0.000510] LSM: Security Framework initializing
[    0.000546] Yama: becoming mindful.
[    0.000654] AppArmor: AppArmor initialized
[    0.000713] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.000728] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.002811] rcu: Hierarchical SRCU implementation.
[    0.004073] smp: Bringing up secondary CPUs ...
[    0.005214] Detected VIPT I-cache on CPU1
[    0.005298] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.006065] Detected VIPT I-cache on CPU2
[    0.006106] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006792] Detected VIPT I-cache on CPU3
[    0.006830] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006909] smp: Brought up 1 node, 4 CPUs
[    0.006936] SMP: Total of 4 processors activated.
[    0.006946] CPU features: detected: 32-bit EL0 Support
[    0.006954] CPU features: detected: CRC32 instructions
[    0.026442] CPU: All CPU(s) started at EL2
[    0.026480] alternatives: patching kernel code
[    0.027967] devtmpfs: initialized
[    0.034865] Registered cp15_barrier emulation handler
[    0.034897] Registered setend emulation handler
[    0.035103] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.035126] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.040477] pinctrl core: initialized pinctrl subsystem
[    0.041993] NET: Registered protocol family 16
[    0.044166] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.044219] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.044316] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.044423] audit: initializing netlink subsys (disabled)
[    0.044628] audit: type=2000 audit(0.044:1): state=initialized audit_enabled=0 res=1
[    0.045259] thermal_sys: Registered thermal governor 'fair_share'
[    0.045266] thermal_sys: Registered thermal governor 'bang_bang'
[    0.045274] thermal_sys: Registered thermal governor 'step_wise'
[    0.045281] thermal_sys: Registered thermal governor 'user_space'
[    0.045817] cpuidle: using governor menu
[    0.046120] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.046229] ASID allocator initialised with 65536 entries
[    0.046429] Serial: AMBA PL011 UART driver
[    0.067176] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.067203] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.067213] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.067222] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.069193] cryptd: max_cpu_qlen set to 1000
[    0.140302] raid6: neonx8   gen()  1465 MB/s
[    0.208357] raid6: neonx8   xor()  1097 MB/s
[    0.276433] raid6: neonx4   gen()  1495 MB/s
[    0.344506] raid6: neonx4   xor()  1086 MB/s
[    0.412581] raid6: neonx2   gen()  1419 MB/s
[    0.480659] raid6: neonx2   xor()   999 MB/s
[    0.548733] raid6: neonx1   gen()  1240 MB/s
[    0.616806] raid6: neonx1   xor()   852 MB/s
[    0.684885] raid6: int64x8  gen()  1014 MB/s
[    0.752949] raid6: int64x8  xor()   533 MB/s
[    0.821035] raid6: int64x4  gen()  1127 MB/s
[    0.889106] raid6: int64x4  xor()   577 MB/s
[    0.957200] raid6: int64x2  gen()   962 MB/s
[    1.025271] raid6: int64x2  xor()   509 MB/s
[    1.093377] raid6: int64x1  gen()   716 MB/s
[    1.161452] raid6: int64x1  xor()   373 MB/s
[    1.161460] raid6: using algorithm neonx4 gen() 1495 MB/s
[    1.161466] raid6: .... xor() 1086 MB/s, rmw enabled
[    1.161473] raid6: using neon recovery algorithm
[    1.162800] iommu: Default domain type: Translated 
[    1.163192] SCSI subsystem initialized
[    1.163424] usbcore: registered new interface driver usbfs
[    1.163481] usbcore: registered new interface driver hub
[    1.163522] usbcore: registered new device driver usb
[    1.163872] pps_core: LinuxPPS API ver. 1 registered
[    1.163880] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.163900] PTP clock support registered
[    1.164616] Advanced Linux Sound Architecture Driver Initialized.
[    1.165357] NetLabel: Initializing
[    1.165366] NetLabel:  domain hash size = 128
[    1.165372] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    1.165456] NetLabel:  unlabeled traffic allowed by default
[    1.165940] clocksource: Switched to clocksource arch_sys_counter
[    1.166251] VFS: Disk quotas dquot_6.6.0
[    1.166329] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.167072] AppArmor: AppArmor Filesystem Enabled
[    1.174685] NET: Registered protocol family 2
[    1.175467] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.175492] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    1.175545] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[    1.175648] TCP: Hash tables configured (established 4096 bind 4096)
[    1.175789] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.175818] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    1.176012] NET: Registered protocol family 1
[    1.176696] RPC: Registered named UNIX socket transport module.
[    1.176706] RPC: Registered udp transport module.
[    1.176713] RPC: Registered tcp transport module.
[    1.176719] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.176963] Trying to unpack rootfs image as initramfs...
[    1.775086] Freeing initrd memory: 9812K
[    1.776598] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.783186] Initialise system trusted keyrings
[    1.783258] Key type blacklist registered
[    1.783417] workingset: timestamp_bits=44 max_order=17 bucket_order=0
[    1.789846] zbud: loaded
[    1.791640] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.792531] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.795029] integrity: Platform Keyring initialized
[    1.847743] xor: automatically using best checksumming function   32regs    
[    1.847753] async_tx: api initialized (async)
[    1.847773] Key type asymmetric registered
[    1.847783] Asymmetric key parser 'x509' registered
[    1.847843] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.847988] io scheduler mq-deadline registered
[    1.847998] io scheduler kyber registered
[    1.848127] io scheduler bfq registered
[    1.851568] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[    1.855788] sun50i-h5-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    1.862589] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    1.864380] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pa not found, using dummy regulator
[    1.864956] printk: console [ttyS0] disabled
[    1.865054] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 34, base_baud = 1500000) is a 16550A
[    2.821052] printk: console [ttyS0] enabled
[    2.829254] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.841632] loop: module loaded
[    2.846408] libphy: Fixed MDIO Bus: probed
[    2.851379] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.857929] ehci-platform: EHCI generic platform driver
[    2.863409] ehci-platform 1c1a000.usb: EHCI Host Controller
[    2.869025] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    2.876921] ehci-platform 1c1a000.usb: irq 19, io mem 0x01c1a000
[    2.897962] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    2.904320] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.912591] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.919816] usb usb1: Product: EHCI Host Controller
[    2.924698] usb usb1: Manufacturer: Linux 5.10.21-sunxi64 ehci_hcd
[    2.930880] usb usb1: SerialNumber: 1c1a000.usb
[    2.935982] hub 1-0:1.0: USB hub found
[    2.939776] hub 1-0:1.0: 1 port detected
[    2.944642] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.950846] ohci-platform: OHCI generic platform driver
[    2.956245] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    2.962882] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    2.970736] ohci-platform 1c1a400.usb: irq 20, io mem 0x01c1a400
[    3.038130] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    3.046408] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.053636] usb usb2: Product: Generic Platform OHCI controller
[    3.059561] usb usb2: Manufacturer: Linux 5.10.21-sunxi64 ohci_hcd
[    3.065745] usb usb2: SerialNumber: 1c1a400.usb
[    3.070783] hub 2-0:1.0: USB hub found
[    3.074609] hub 2-0:1.0: 1 port detected
[    3.079869] usbcore: registered new interface driver usb-storage
[    3.086476] mousedev: PS/2 mouse device common for all mice
[    3.093012] sun6i-rtc 1f00000.rtc: registered as rtc0
[    3.098118] sun6i-rtc 1f00000.rtc: setting system clock to 2021-04-14T17:28:10 UTC (1618421290)
[    3.106820] sun6i-rtc 1f00000.rtc: RTC enabled
[    3.111382] i2c /dev entries driver
[    3.115877] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    3.125167] sdhci: Secure Digital Host Controller Interface driver
[    3.131371] sdhci: Copyright(c) Pierre Ossman
[    3.135777] Synopsys Designware Multimedia Card Interface Driver
[    3.142474] sdhci-pltfm: SDHCI platform and OF driver helper
[    3.142571] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pf not found, using dummy regulator
[    3.148290] sun8i-h3-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator
[    3.165492] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    3.170240] ledtrig-cpu: registered to indicate activity on CPUs
[    3.176798] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    3.183573] sun8i-ce 1c15000.crypto: Set mod clock to 300000000 (300 Mhz) from 24000000 (24 Mhz)
[    3.192622] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    3.195457] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    3.200317] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    3.216840] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    3.224513] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    3.232157] sun8i-ce 1c15000.crypto: Register cbc(aes)
[    3.237473] sun8i-ce 1c15000.crypto: Register ecb(aes)
[    3.242744] sun8i-ce 1c15000.crypto: Register cbc(des3_ede)
[    3.248459] sun8i-ce 1c15000.crypto: Register ecb(des3_ede)
[    3.254151] sun8i-ce 1c15000.crypto: Register md5
[    3.258978] sun8i-ce 1c15000.crypto: Register sha1
[    3.262121] mmc0: host does not support reading read-only switch, assuming write-enable
[    3.263884] sun8i-ce 1c15000.crypto: Register sha224
[    3.276845] sun8i-ce 1c15000.crypto: Register sha256
[    3.279284] mmc0: new high speed SDHC card at address e624
[    3.281965] sun8i-ce 1c15000.crypto: DEBUG: Algo of sha384 not supported
[    3.288285] mmcblk0: mmc0:e624 SC16G 14.8 GiB 
[    3.293992] sun8i-ce 1c15000.crypto: DEBUG: Algo of sha512 not supported
[    3.294000] sun8i-ce 1c15000.crypto: Register stdrng
[    3.304804]  mmcblk0: p1
[    3.305310] sun8i-ce 1c15000.crypto: TRNG not supported
[    3.317856] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 0
[    3.323808] hid: raw HID events driver (C) Jiri Kosina
[    3.329083] usbcore: registered new interface driver usbhid
[    3.334659] usbhid: USB HID core driver
[    3.348701] NET: Registered protocol family 10
[    3.395615] Segment Routing with IPv6
[    3.399427] NET: Registered protocol family 17
[    3.404067] 8021q: 802.1Q VLAN Support v1.8
[    3.408447] 9pnet: Installing 9P2000 support
[    3.412812] Key type dns_resolver registered
[    3.417652] registered taskstats version 1
[    3.421774] Loading compiled-in X.509 certificates
[    3.430841] Loaded X.509 cert 'Build time autogenerated kernel key: b55cc50c0b5861053e31ca5c6be0f880e49735e6'
[    3.445210] zswap: loaded using pool zstd/z3fold
[    3.450128] Key type ._fscrypt registered
[    3.454156] Key type .fscrypt registered
[    3.458083] Key type fscrypt-provisioning registered
[    3.464415] Btrfs loaded, crc32c=crc32c-generic
[    3.489213] Key type encrypted registered
[    3.493288] AppArmor: AppArmor sha1 policy hashing enabled
[    3.498834] ima: No TPM chip found, activating TPM-bypass!
[    3.504357] ima: Allocated hash algorithm: sha1
[    3.508923] ima: No architecture policies found
[    3.513541] evm: Initialising EVM extended attributes:
[    3.518684] evm: security.selinux
[    3.522003] evm: security.SMACK64
[    3.525313] evm: security.SMACK64EXEC
[    3.528977] evm: security.SMACK64TRANSMUTE
[    3.533075] evm: security.SMACK64MMAP
[    3.536739] evm: security.apparmor
[    3.540143] evm: security.ima
[    3.543114] evm: security.capability
[    3.546692] evm: HMAC attrs: 0x1
[    3.560238] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pd not found, using dummy regulator
[    3.570077] sun50i-h5-pinctrl 1c20800.pinctrl: supply vcc-pg not found, using dummy regulator
[    3.580331] ehci-platform 1c1b000.usb: EHCI Host Controller
[    3.585957] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3
[    3.593842] ehci-platform 1c1b000.usb: irq 21, io mem 0x01c1b000
[    3.613942] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00
[    3.620313] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    3.628589] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.635816] usb usb3: Product: EHCI Host Controller
[    3.640697] usb usb3: Manufacturer: Linux 5.10.21-sunxi64 ehci_hcd
[    3.646887] usb usb3: SerialNumber: 1c1b000.usb
[    3.651983] hub 3-0:1.0: USB hub found
[    3.655780] hub 3-0:1.0: 1 port detected
[    3.660818] ehci-platform 1c1c000.usb: EHCI Host Controller
[    3.666426] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4
[    3.674316] ehci-platform 1c1c000.usb: irq 23, io mem 0x01c1c000
[    3.693941] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    3.700296] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    3.708565] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.715792] usb usb4: Product: EHCI Host Controller
[    3.720674] usb usb4: Manufacturer: Linux 5.10.21-sunxi64 ehci_hcd
[    3.726855] usb usb4: SerialNumber: 1c1c000.usb
[    3.731883] hub 4-0:1.0: USB hub found
[    3.735674] hub 4-0:1.0: 1 port detected
[    3.740627] ehci-platform 1c1d000.usb: EHCI Host Controller
[    3.746226] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5
[    3.754103] ehci-platform 1c1d000.usb: irq 25, io mem 0x01c1d000
[    3.773941] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00
[    3.780248] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    3.788518] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.795743] usb usb5: Product: EHCI Host Controller
[    3.800630] usb usb5: Manufacturer: Linux 5.10.21-sunxi64 ehci_hcd
[    3.806813] usb usb5: SerialNumber: 1c1d000.usb
[    3.811832] hub 5-0:1.0: USB hub found
[    3.815630] hub 5-0:1.0: 1 port detected
[    3.820586] ohci-platform 1c1b400.usb: Generic Platform OHCI controller
[    3.827227] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6
[    3.835097] ohci-platform 1c1b400.usb: irq 22, io mem 0x01c1b400
[    3.902124] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    3.910394] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.917618] usb usb6: Product: Generic Platform OHCI controller
[    3.923543] usb usb6: Manufacturer: Linux 5.10.21-sunxi64 ohci_hcd
[    3.929725] usb usb6: SerialNumber: 1c1b400.usb
[    3.935340] hub 6-0:1.0: USB hub found
[    3.939130] hub 6-0:1.0: 1 port detected
[    3.944080] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[    3.950729] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7
[    3.958603] ohci-platform 1c1c400.usb: irq 24, io mem 0x01c1c400
[    4.026123] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    4.034393] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.041617] usb usb7: Product: Generic Platform OHCI controller
[    4.047542] usb usb7: Manufacturer: Linux 5.10.21-sunxi64 ohci_hcd
[    4.053724] usb usb7: SerialNumber: 1c1c400.usb
[    4.058736] hub 7-0:1.0: USB hub found
[    4.062525] hub 7-0:1.0: 1 port detected
[    4.067475] ohci-platform 1c1d400.usb: Generic Platform OHCI controller
[    4.074125] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8
[    4.081999] ohci-platform 1c1d400.usb: irq 26, io mem 0x01c1d400
[    4.150130] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    4.158405] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.165629] usb usb8: Product: Generic Platform OHCI controller
[    4.171555] usb usb8: Manufacturer: Linux 5.10.21-sunxi64 ohci_hcd
[    4.177737] usb usb8: SerialNumber: 1c1d400.usb
[    4.182762] hub 8-0:1.0: USB hub found
[    4.186551] hub 8-0:1.0: 1 port detected
[    4.191531] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator
[    4.201083] musb-hdrc musb-hdrc.2.auto: MUSB HDRC host driver
[    4.206858] musb-hdrc musb-hdrc.2.auto: new USB bus registered, assigned bus number 9
[    4.214773] phy id_det change to device
[    4.218780] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    4.227050] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.234273] usb usb9: Product: MUSB HDRC host driver
[    4.239243] usb usb9: Manufacturer: Linux 5.10.21-sunxi64 musb-hcd
[    4.245424] usb usb9: SerialNumber: musb-hdrc.2.auto
[    4.250974] hub 9-0:1.0: USB hub found
[    4.254770] hub 9-0:1.0: 1 port detected
[    4.261426] scpi_protocol scpi: SCP Protocol 0.0 Firmware 0.0.0 version
[    4.268656] of_cfs_init
[    4.271261] of_cfs_init: OK
[    4.274237] ALSA device list:
[    4.277203]   No soundcards found.
[    4.283154] Freeing unused kernel memory: 2496K
[    4.287908] Run /init as init process
Loading, please wait...
Starting version 241
[    4.703415] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found
[    4.709971] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found
[    4.716345] dwmac-sun8i 1c30000.ethernet: supply phy-io not found, using dummy regulator
[    4.725788] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    4.731756] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 50006 (expect 58000)
[    4.846330] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[    4.853590] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[    4.860817] dwmac-sun8i 1c30000.ethernet: COE Type 2
[    4.865785] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[    4.872579] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[    4.878253] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[    4.884530] libphy: stmmac: probed
[    4.889217] dwmac-sun8i 1c30000.ethernet: Found internal PHY node
[    4.895837] libphy: mdio_mux: probed
[    4.899451] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY
[    4.905817] dwmac-sun8i 1c30000.ethernet: Powering internal PHY
[    4.922900] libphy: mdio_mux: probed
[    4.926538] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
done.
Begin: Will now check root file system ... fsck from util-linux 2.33.1
[/sbin/fsck.ext4[    5.268027] random: fast init done
 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 
/dev/mmcblk0p1: clean, 44046/1106368 files, 443014/3849616 blocks
done.
[    5.303764] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.233028] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    6.254964] systemd[1]: Detected architecture arm64.

Welcome to Debian GNU/Linux 10 (buster)!

[    6.309779] systemd[1]: Set hostname to <nanopineo2>.
[    6.911531] random: systemd: uninitialized urandom read (16 bytes read)
[    6.931111] random: systemd: uninitialized urandom read (16 bytes read)
[    6.938456] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[  OK  ] Started Forward Password R…uests to Wall Directory Watch.
[    6.962563] random: systemd: uninitialized urandom read (16 bytes read)
[    6.969831] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[  OK  ] Set up automount Arbitrary…s File System Automount Point.
[    6.998771] systemd[1]: Listening on fsck to fsckd communication Socket.
[  OK  ] Listening on fsck to fsckd communication Socket.
[    7.022834] systemd[1]: Listening on Journal Socket.
[  OK  ] Listening on Journal Socket.
[    7.049713] systemd[1]: Mounting Huge Pages File System...
         Mounting Huge Pages File System...
[    7.071257] systemd[1]: Listening on Journal Audit Socket.
[  OK  ] Listening on Journal Audit Socket.
[    7.099461] systemd[1]: Mounting Kernel Debug File System...
         Mounting Kernel Debug File System...
[  OK  ] Listening on udev Kernel Socket.
         Mounting POSIX Message Queue File System...
[  OK  ] Reached target Swap.
         Starting Restore / save the current clock...
[  OK  ] Listening on udev Control Socket.
         Starting Load Kernel Modules...
[  OK  ] Created slice User and Session Slice.
[  OK  ] Reached target Slices.
[  OK  ] Created slice system-serial\x2dgetty.slice.
         Starting Nameserver information manager...
[  OK  ] Listening on Journal Socket (/dev/log).
[    7.326534] g_serial gadget: Gadget Serial v2.4
[    7.326551] g_serial gadget: g_serial ready
[  OK  ] Reached target Remote File Systems.
[  OK  ] Reached target System Time Synchronized.
[  OK  ] Reached target Local Encrypted Volumes.
         Starting Set the console keyboard layout...
[  OK  ] Created slice system-getty.slice.
         Starting Remount Root and Kernel File Systems...
         Starting udev Coldplug all Devices...
         Starting Create list of re…odes for the current kernel...
[  OK  ] Reached target Path[    7.498364] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
s.
[  OK  ] Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on Syslog Socket.
[  OK  ] Mounted Huge Pages File System.
[  OK  ] Mounted Kernel Debug File System.
[  OK  ] Mounted POSIX Message Queue File System.
[  OK  ] Started Restore / save the current clock.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Started Create list of req… nodes for the current kernel.
[  OK  ] Started Nameserver information manager.
         Starting Load/Save Random Seed...
         Starting Create System Users...
         Mounting Kernel Configuration File System...
         Starting Apply Kernel Variables...
[  OK  ] Mounted Kernel Configuration File System.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Set the console keyboard layout.
[  OK  ] Started Create System Users.
[  OK  ] Started Apply Kernel Variables.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Started udev Coldplug all Devices.
         Starting Helper to synchronize boot up for ifupdown...
[  OK  ] Started Create Static Device Nodes in /dev.
         Starting udev Kernel Device Manager...
[  OK  ] Reached target Local File Systems (Pre).
         Mounting /tmp...
[  OK  ] Mounted /tmp.
[  OK  ] Reached target Local File Systems.
         Starting Set console font and keymap...
         Starting Armbian ZRAM config...
[  OK  ] Started Set console font and keymap.
[  OK  ] Started udev Kernel Device Manager.
[  OK  ] Found device /dev/ttyGS0.
[    8.342448] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1300000, not supported by regulator
[    8.352449] cpu cpu0: _opp_add: OPP not supported by regulators (960000000)
[    8.359684] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1300000, not supported by regulator
[    8.369685] cpu cpu0: _opp_add: OPP not supported by regulators (1008000000)
[    8.376934] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV: 1320000, not supported by regulator
[    8.386901] cpu cpu0: _opp_add: OPP not supported by regulators (1104000000)
[    8.394245] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV: 1320000, not supported by regulator
[    8.404224] cpu cpu0: _opp_add: OPP not supported by regulators (1200000000)
[    8.411476] core: _opp_supported_by_regulators: OPP minuV: 1340000 maxuV: 1340000, not supported by regulator
[    8.421476] cpu cpu0: _opp_add: OPP not supported by regulators (1296000000)
[    8.428838] core: _opp_supported_by_regulators: OPP minuV: 1400000 maxuV: 1400000, not supported by regulator
[    8.438832] cpu cpu0: _opp_add: OPP not supported by regulators (1368000000)
[    8.446777] thermal thermal_zone0: binding zone cpu-thermal with cdev thermal-cpufreq-0 failed:-22
[    8.490154] mc: Linux media interface: v0.10
[    8.551535] videodev: Linux video capture interface: v2.00
[    8.663781] sunxi_cedrus: module is from the staging directory, the quality is unknown, you have been warned.
[    8.690177] cedrus 1c0e000.video-codec: Device registered as /dev/video0
[    8.713016] zram: Added device: zram0
[    8.722810] zram: Added device: zram1
[    8.728605] zram: Added device: zram2
[  OK  ] Found device /dev/ttyS0.
[  OK  ] Started Helper to synchronize boot up for ifupdown.
[    8.940300] zram0: detected capacity change from 0 to 248942592
         Starting Raise network interfaces...
[    9.509285] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.2:07] driver [RTL8211E Gigabit Ethernet] (irq=POLL)
[    9.520344] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found
[    9.527683] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available
[    9.535369] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW
[    9.542520] dwmac-sun8i 1c30000.ethernet eth0: configuring for phy/rgmii-id link mode
[   10.014017] Adding 243104k swap on /dev/zram0.  Priority:5 extents:1 across:243104k SSFS
[   10.214853] zram1: detected capacity change from 0 to 52428800
[   12.301033] systemd[1]: Started Armbian ZRAM config.
[  OK  ] Started Armbian ZRAM config.
[   12.334229] systemd[1]: Starting Armbian memory supported logging...
         Starting Armbian memory supported logging...
[   12.450147] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[   12.457432] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   13.634794] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   13.643233] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.541522] systemd[1]: Started Raise network interfaces.
[  OK  ] Started Raise network interfaces.
[   16.018765] systemd[1]: Started Armbian memory supported logging.
[  OK  ] Started Armbian memory supported logging.
[   16.050970] systemd[1]: Starting Journal Service...
         Starting Journal Service...
[   16.296052] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.
         Starting Flush Journal to Persistent Storage...
[   16.394921] systemd-journald[583]: Received request to flush runtime journal from PID 1
[  OK  ] Started Flush Journal to Persistent Storage.
         Starting Create Volatile Files and Directories...
[  OK  ] Started Create Volatile Files and Directories.
[  OK  ] Started Entropy daemon using the HAVEGE algorithm.
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Reached target System Initialization.
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Started Daily man-db regeneration.
[  OK  ] Started Daily apt download activities.
[  OK  ] Started Daily apt upgrade and clean activities.
[  OK  ] Started Daily rotation of log files.
[  OK  ] Reached target Timers.
         Starting Armbian hardware monitoring...
         Starting Armbian hardware optimization...
[  OK  ] Started Armbian hardware monitoring.
[  OK  ] Started Armbian hardware optimization.
[  OK  ] Reached target Basic System.
[  OK  ] Started Regular background program processing daemon.
[  OK  ] Started D-Bus System Message Bus.
         Starting WPA supplicant...
         Starting System Logging Service...
         Starting LSB: Load kernel …d to enable cpufreq scaling...
         Starting Login Service...
         Starting Network Manager...
         Starting Resets System Activity Data Collector...
         Starting Dispatcher daemon for systemd-networkd...
         Starting rng-tools.service...
[  OK  ] Started Resets System Activity Data Collector.
[   17.555432] random: crng init done
[   17.558999] random: 7 urandom warning(s) missed due to ratelimiting
[  OK  ] Started System Logging Service.
[  OK  ] Started rng-tools.service.
[  OK  ] Started Login Service.
[  OK  ] Started WPA supplicant.
[  OK  ] Started LSB: Load kernel m…ded to enable cpufreq scaling.
         Starting LSB: set CPUFreq kernel parameters...
[  OK  ] Started LSB: set CPUFreq kernel parameters.
         Starting LSB: Set sysfs variables from /etc/sysfs.conf...
[  OK  ] Started LSB: Set sysfs variables from /etc/sysfs.conf.
[  OK  ] Started Network Manager.
[  OK  ] Reached target Network.
         Starting Permit User Sessions...
[  OK  ] Started Unattended Upgrades Shutdown.
         Starting OpenBSD Secure Shell server...
[  OK  ] Reached target Network is Online.
         Starting LSB: Advanced IEEE 802.11 management daemon...
         Starting /etc/rc.local Compatibility...
         Starting chrony, an NTP client/server...
[  OK  ] Started Permit User Sessions.
[  OK  ] Started LSB: Advanced IEEE 802.11 management daemon.
[  OK  ] Started /etc/rc.local Compatibility.
         Starting Hostname Service...
[  OK  ] Started Serial Getty on ttyGS0.
[  OK  ] Started Serial Getty on ttyS0.
[  OK  ] Started Getty on tty1.
[  OK  ] Reached target Login Prompts.
[  OK  ] Started OpenBSD Secure Shell server.
[  OK  ] Started chrony, an NTP client/server.
[  OK  ] Started Hostname Service.
[  OK  ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
         Starting Network Manager Script Dispatcher Service...
[  OK  ] Started Network Manager Script Dispatcher Service.
[  OK  ] Started Dispatcher daemon for systemd-networkd.
[  OK  ] Reached target Multi-User System.
[  OK  ] Reached target Graphical Interface.
         Starting Update UTMP about System Runlevel Changes...
[  OK  ] Started Update UTMP about System Runlevel Changes.

Armbian 21.02.3 Buster ttyS0 

nanopineo2 login: 
nanopineo2 login: root
Last login: Wed Apr 14 17:23:22 UTC 2021 on ttyS0
 _   _ ____  _   _   _              ____  
| \ | |  _ \(_) | \ | | ___  ___   |___ \ 
|  \| | |_) | | |  \| |/ _ \/ _ \    __) |
| |\  |  __/| | | |\  |  __/ (_) |  / __/ 
|_| \_|_|   |_| |_| \_|\___|\___/  |_____|
                                          
Welcome to Armbian 21.02.3 Buster with Linux 5.10.21-sunxi64

System load:   17%           	Up time:       0 min		
Memory usage:  22% of 474M   	IP:            192.168.31.33
CPU temp:      33°C           	Usage of /:    10% of 15G    	

[ General system configuration (beta): armbian-config ]

Il faut donc répondre à la question ?
Ou se trouve la différence entre le noyau/firmware/dts entre Debian et Armbian pour que le réseau fonctionne ?
Je penche sur une histoire d'overlay des DTB ? et/ou sur l'init du Phy ....
:evil:
Cordialement
-W.-
Posts: 121
Joined: Sun Mar 22, 2020 5:26 pm
Location: Allier

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by -W.- »

Hello

Est ce que dans tes recherches tu as vu ce post là ? Peut être est ce en rapport.

Il y a aussi celui là les boards sont quasi identiques l image se tente pour voir...
Mais à priori d'autres ont rencontré des soucis...

Les Neo 2 sont dans les cartes que je n'a pas encore retrouvées, pour le moment je ne peux rien faire de plus que de te proposer une séance de brainstorming demain :?

@+
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,
Merci de l'info, je suis en train de reproduire la nouvelle image du projet vmdb2-wrapper pour usage sur une nanopineo2 avec boîtier et interface oled
affaire a suivre
:(
Cordialement
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,
Hélas, la version à jour du projet vmdb2-wrapper ne résouds pas le problème du port Ethernet. :evil:
Après plusieurs recherches avec Jérôme, je suis partie sur la version d'Armbian en Debian Buster qui résouds
nativement ce problème.
:cry:
Cordialement
-W.-
Posts: 121
Joined: Sun Mar 22, 2020 5:26 pm
Location: Allier

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by -W.- »

Hello

De mon coté je n'ai toujours pas retrouvé mes Neo bien que 75% de mon sous sol ait été ratissé. Ce qui m'embete bien plus c'est qu'il manque donc toujours aussi les clusters de pine 64, et d'orange pi Zero et le T1040 :(

Maintenant que cela tourne tu pourrais stp nous publier des photos du boîtier Led de ta Neo 2 ?

@ suivre
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,
En effet, l'équipement est maintenant bien intégré dans son réseau avec son rôle.
Pour mémoire, la nanopi-neo2 semble être obsolète puisque remplacée par les versions nanopi-neo3 et nanopi-neo4.
Hélas, le super boitier ALU usiné dans la masse (donc parfait en tant que radiateur!) pour la nanopi-neo2 ne semble ni compatible des versions ultérieures, ni disponible sur les versions ultérieures, sauf erreur de ma part.

Pour les photos, merci de me fournir un site perrenne permettant de mettre à disposition les photos, les seuls sites que j'utilise ont une limite de date :D
Cordialement
jeanmarc
Posts: 130
Joined: Sun Mar 22, 2020 5:28 pm
Location: Essonne

Re: [nanopi neo2] [boot image vmdb2-wrapper]

Post by jeanmarc »

Bonjour,
A défaut, les photos de l'objet décrites ici sont bien ....
https://fra.grandado.com/products/nanop ... gLWc_D_BwE
:D
Cordialement
Post Reply